Tilt stand to fit Arturia RackBrute 6U – 15°, 25° or 35°, two side wedges of two parts each

Description

Lying flat on the desk you see knobs and jacks at a low angle and the legends are hard to read. Two side wedges under the ends of the case tilt it towards you by 15, 25 or 35 degrees. The case rests on its flat underside only, leans against a low lip at the front and is held by a flat stop at the back. The wedge does not touch handles or end caps, because there are no dimensions for them.

• At the outer dimensions: support of 301 mm (300 mm case depth + 1 mm clearance) between the lip (10 mm high) and the stop (6 mm high), wedge 32 mm wide.
• Two parts per wedge: one wedge is longer than a 220 mm print bed. Slide the front and rear part together sideways over two dovetails; the left and right wedge are identical.
• Pockets for rubber feet Ø 12–12.7 mm on the underside (4 per wedge) so nothing slides.
• Truss instead of solid material: printed lying on the side cheek, no supports.
• Ready for the side shelf: two square holes in the wedge take its tongues; the shelf is a separate product and does not touch the case.

Variants: One set of two wedges per angle: 15° 301 mm long, 91 mm high at the back; 25° 284 mm long, 140 mm high at the back; 35° 259 mm long, 186 mm high at the back. Arturia gives no angle; 15°, 25° and 35° are our choice.

Dimensions: Dimensions taken from Arturia RackBrute 6U (maker's page) and RackBrute manual; our part has not been tested on a case yet. Outer size 484 × 300 × 83 mm; lying flat we take 300 mm as the depth from front to back and 83 mm as the height, with 1 mm clearance. The assignment of the three numbers to width, depth and height is our estimate. Please measure the outer dimensions of your own case before printing; the manufacturer only gives rounded numbers. Print the free fit gauge first: it shows whether hole pattern, screws and your printer work together.

Load: For the case on the desk, guide value up to 5 kg, not a tested load rating, not a seat or a shelf.

Material: PETG, or ASA. No PLA: the case presses on the wedges all the time, and PLA creeps under constant load, even more so in warm rooms.

Brands: Fits Arturia RackBrute; not an accessory by the manufacturers, no affiliation with them. No logos and no lettering on the parts.

Clearance 1 mm on the case depth; measure your own case.

Dimensions

Dimensions of the default variant in print orientation.

Material and temperature

Print stands and shelf in PETG (ASA works too): a case with modules weighs several kilos, and PLA slowly gives way under constant load. Print panels and gauge in PLA (PETG works too). Do not put a heat source right next to them, such as a radiator, and do not leave the parts in the sun behind glass.

Print orientation: Lying on the side cheek, no supports.

Safety notice

For the case on the desk, guide value up to 5 kg, not a tested load rating, not a seat or a shelf. The part has no electronics and carries no current. Put the wedges on a flat, firm surface and do not push the case over the lip. Not a toy and not an electrical part: the stands only carry the case on the desk (guide value up to 5 kg), the shelf 0.5 kg at most; neither is a tested load rating. None of it carries current.

Not an original part. No affiliation with the manufacturers named; brand and model names only indicate fitment.

What's included

You get one ZIP for the version you choose, with:

• STL – print-ready mesh
• 3MF – with print profile
• STEP – editable in CAD

Files per version

Version	Contains	Price
15° tilt (2 wedges of 2 parts each)	neigungsstaender-arturia-rackbrute-6u_15grad_keil_vorn.stl, neigungsstaender-arturia-rackbrute-6u_15grad_keil_vorn.3mf, neigungsstaender-arturia-rackbrute-6u_15grad_keil_vorn.step, neigungsstaender-arturia-rackbrute-6u_15grad_keil_hinten.stl, neigungsstaender-arturia-rackbrute-6u_15grad_keil_hinten.3mf, neigungsstaender-arturia-rackbrute-6u_15grad_keil_hinten.step	€3.90
25° tilt (2 wedges of 2 parts each)	neigungsstaender-arturia-rackbrute-6u_25grad_keil_vorn.stl, neigungsstaender-arturia-rackbrute-6u_25grad_keil_vorn.3mf, neigungsstaender-arturia-rackbrute-6u_25grad_keil_vorn.step, neigungsstaender-arturia-rackbrute-6u_25grad_keil_hinten.stl, neigungsstaender-arturia-rackbrute-6u_25grad_keil_hinten.3mf, neigungsstaender-arturia-rackbrute-6u_25grad_keil_hinten.step	€3.90
35° tilt (2 wedges of 2 parts each)	neigungsstaender-arturia-rackbrute-6u_35grad_keil_vorn.stl, neigungsstaender-arturia-rackbrute-6u_35grad_keil_vorn.3mf, neigungsstaender-arturia-rackbrute-6u_35grad_keil_vorn.step, neigungsstaender-arturia-rackbrute-6u_35grad_keil_hinten.stl, neigungsstaender-arturia-rackbrute-6u_35grad_keil_hinten.3mf, neigungsstaender-arturia-rackbrute-6u_35grad_keil_hinten.step	€3.90

You will also need

• 8 × Self-adhesive rubber foot Ø 12–12.7 mm, up to 3 mm high (optional)
• 1 × Glue that holds PETG (optional, for the joint)

Printing

1. PETG (or ASA), 0.4 mm nozzle, 0.2 mm layers, 3 walls, 15 % gyroid, no supports.
2. Lying on the side cheek, as the file is laid out; print two (or two front and two rear parts).

Installation

1. Slide the front and rear part of each wedge together sideways.
2. Take off or turn away the handle and Link parts. Put the wedges on a flat, firm surface, lip towards you, one under each end of the case.
3. Lay the case on until it rests against both lips at the front. Check that nothing gets caught at the lip and the stop.

FAQ

Reviews

No reviews yet.

How we check reviews: only people who bought or downloaded the file for free in our shop can review, via the personal link from the download email; once per order and file. Anyone who received the files in return for something (cooperations, gifts, 100% codes) cannot review. We publish all reviews, negative ones too, and only remove unlawful content or spam. There is no reward for reviews.

Version 2.0.0, updated 5 November 2026 · SKU F2-EU-RB6U-STAND