Triple 52 mm gauge pod for the dashboard – angled toward the driver, stick-on

Description

The pod sticks on top of the dashboard and holds three 52 mm gauges side by side. The outer ones are angled 12° toward the driver, so all three dials are easy to read.

• Three tilt angles (60, 75 and 90°) compensate for the slope of the dashboard.
• The flat base is 203 × 70 mm for double-sided VHB tape. Nothing is drilled.
• One M3 set screw on top per gauge secures them.
• The cables run forward through the hollow stands.
• Prints without supports on a 220 mm bed.

Important: the top of the dashboard reaches ~89 °C in summer. Use ASA or ABS only.

VHB tape absorbs slight curvature; on strongly curved dashboards add a TPU shim. Bore +0.4 mm, verify with the test ring.

Dimensions

Dimensions of the default variant in print orientation.

Material and temperature

Location in direct sun: print in ASA or ABS only. A dashboard reaches about 69 °C on average after one hour in the sun, with peaks up to 89 °C. ASA only softens at around 108 °C and is UV resistant. PETG and PLA will warp here.

Print orientation: Front face (toward the windscreen) on the bed, cup pointing up.

Guide: PETG or ASA in a car?

Safety notice

Stick it on the driver's side only, never on or in front of the passenger airbag cover. The pod must not block the view through the windscreen or of the speedometer and warning lights. Check it is secure before driving. Install at your own risk. Never mount in an airbag deployment zone, never cover controls, never restrict the view. Follow the material and temperature advice. Add-ons may affect the type approval of the vehicle (§ 19 StVZO in Germany); keep edges in the head and knee area rounded (UN Regulation No. 21).

Not an original part. No affiliation with the vehicle manufacturers named; make and model names only indicate fitment.

What's included

• toleranz-testring-52mm.stl – Tolerance test ring
• armaturenbrett-gauge-pod-dreifach-52mm_neigung60.stl – STL – print-ready mesh
• armaturenbrett-gauge-pod-dreifach-52mm_neigung60.3mf – 3MF – with print profile
• armaturenbrett-gauge-pod-dreifach-52mm_neigung60.step – STEP – editable in CAD
• armaturenbrett-gauge-pod-dreifach-52mm_neigung75.stl – STL – print-ready mesh
• armaturenbrett-gauge-pod-dreifach-52mm_neigung75.3mf – 3MF – with print profile
• armaturenbrett-gauge-pod-dreifach-52mm_neigung75.step – STEP – editable in CAD
• armaturenbrett-gauge-pod-dreifach-52mm_neigung90.stl – STL – print-ready mesh
• armaturenbrett-gauge-pod-dreifach-52mm_neigung90.3mf – 3MF – with print profile
• armaturenbrett-gauge-pod-dreifach-52mm_neigung90.step – STEP – editable in CAD

You will also need

• 1 × VHB tape 3M 5952 or similar, 2 strips 25 × 200 mm
• 3 × M3 set screw or self-tapping M3 screw, 8–10 mm

Printing

1. Print the tolerance test ring first and test-fit the gauge.
2. Print in ASA or ABS (enclosed printer recommended), 0.2 mm layers, 4 walls, 20 % infill, no supports. No PETG and no PLA: the dashboard gets too hot.

Installation

1. Degrease the dashboard with isopropyl alcohol; on textured plastic apply adhesion promoter (3M Primer 94).
2. Feed the cable through the stand from the front, insert the gauge, tighten the set screw hand-tight.
3. Apply the VHB tape to the base, align the pod and press firmly for 30 s. Let it cure for 24 h.

Guides for this part

• Gauge pod without drilling: cupholder, vent, steering column, dashboard or cage?

FAQ

Version 2.0.0, updated 2 November 2026 · SKU GP-UNI-DASH-3X52