Token tube with snap lid with placeholder contents (no artwork)

Board game accessories

Token tube with snap lid – for coins, markers and chips Ø 20, 25, 30 or 40 mm

Tube for round game tokens, 60 mm deep, with a lid that clicks on without a thread. Four diameters, printed without supports.

Choose a version
€1.49incl. VAT

The seller is Sold through Link, LLC (Stripe), which also processes the payment; Link's "Sold through Link" terms apply and Link sends the receipt. You choose payment methods such as card, Apple Pay, Google Pay and Link in the next step. The download is available right after payment. As an EU consumer you can cancel within 14 days of receiving access (cancellation policy). Our licence terms apply to the files.

Licence: use and print for yourself; do not share or sell the files or printed parts. Licence terms · Print commercially or subscribe? Register interest

Description

Coins, markers and chips stay together in a stack and do not spill into the box when you pack up. The lid clicks into a groove on the tube with four spring fingers.

  • Four diameters: for tokens Ø 20, 25, 30 and 40 mm, 1 mm wider inside, 60 mm deep (e.g. 30 markers of 2 mm or 18 chips of 3.3 mm).
  • Snap lid without a thread: just pull it off to open.

Dimensions: No foreign dimension (the token diameter is the variant); our part has not been printed yet. If the lid snaps too tightly, smooth the groove with fine sandpaper.

Material: PLA is enough, PETG works too. Do not leave it in the sun or a hot car: PLA softens from about 55 °C.

Not a toy. Storage for game components and small parts; keep out of reach of small children.

Dimensions

Width29 mm
Height62 mm
Depth29 mm
Weight (printed)15 g
Layer height0.2 mm
Walls2
Infill15 %

Dimensions of the default variant in print orientation.

Material and temperature

PLA is enough: the parts bear no load and do not get warm. They are not meant for contact with food. PLA softens in a hot car or in the sun behind glass, so better not leave the parts there.

Print orientation: Tube upright, lid upside down.

Safety notice

Not a toy. Storage for game components and small parts; keep out of reach of small children. Do not store in the sun or a hot car. Not a toy. Storage for game components and small parts; keep out of reach of small children.

Not an original part. No affiliation with the vehicle or device manufacturers named; make and model names only indicate fitment.

What's included

You get one ZIP for the version you choose, with:

  • STL – print-ready mesh
  • 3MF – with print profile
  • STEP – editable in CAD
Files per version
VersionContainsPrice
for tokens Ø 20 mmtoken-roehre-schnappdeckel_d20_roehre.stl, token-roehre-schnappdeckel_d20_roehre.3mf, token-roehre-schnappdeckel_d20_roehre.step, token-roehre-schnappdeckel_d20_deckel.stl, token-roehre-schnappdeckel_d20_deckel.3mf, token-roehre-schnappdeckel_d20_deckel.step€1.49
for tokens Ø 25 mmtoken-roehre-schnappdeckel_d25_roehre.stl, token-roehre-schnappdeckel_d25_roehre.3mf, token-roehre-schnappdeckel_d25_roehre.step, token-roehre-schnappdeckel_d25_deckel.stl, token-roehre-schnappdeckel_d25_deckel.3mf, token-roehre-schnappdeckel_d25_deckel.step€1.49
for tokens Ø 30 mmtoken-roehre-schnappdeckel_d30_roehre.stl, token-roehre-schnappdeckel_d30_roehre.3mf, token-roehre-schnappdeckel_d30_roehre.step, token-roehre-schnappdeckel_d30_deckel.stl, token-roehre-schnappdeckel_d30_deckel.3mf, token-roehre-schnappdeckel_d30_deckel.step€1.49
for tokens Ø 40 mmtoken-roehre-schnappdeckel_d40_roehre.stl, token-roehre-schnappdeckel_d40_roehre.3mf, token-roehre-schnappdeckel_d40_roehre.step, token-roehre-schnappdeckel_d40_deckel.stl, token-roehre-schnappdeckel_d40_deckel.3mf, token-roehre-schnappdeckel_d40_deckel.step€1.49

Printing

  1. PLA (or PETG), 0.2 mm layers, 2 walls, 15 % infill, no supports.
  2. Tube upright, lid upside down, as the files are laid out.

FAQ

Which material should I use for this card box?

Recommended: PLA (alternatively PETG). PLA is enough: the parts bear no load and do not get warm. They are not meant for contact with food. PLA softens in a hot car or in the sun behind glass, so better not leave the parts there.

Do I receive a printed part?

No. You get the print files and print the part yourself or use a print service. You get the download link right after payment.

Which material?

PLA is enough, PETG works too. Do not leave it in the sun or a hot car: PLA softens from about 55 °C.

Are there magnets?

No. Lids hold by friction, a groove or a snap nose; magnets are deliberately left out.

Reviews

No reviews yet.

    How we check reviews: only people who bought or downloaded the file for free in our shop can review, via the personal link from the download email; once per order and file. Anyone who received the files in return for something (cooperations, gifts, 100% codes) cannot review. We publish all reviews, negative ones too, and only remove unlawful content or spam. There is no reward for reviews.

    Version 1.0.0, updated 4 November 2026 · SKU BG-TOKEN-TUBE

    Board game accessories for other cars

    All board game accessories